Search
  • e
  • 527

Email

TEL

CONTACT

Address

Room 703,No.28 Huahai Road.Economic and technical development zone,Shenyang P.R.China

ZIP:110143 

ABOUT       NEWS      PRODUCTS      CAPACITY      NETWORK      MESSAGE      CONTACT

+86-024-25558500

 

WE ARE COMMITTED TO PROVIDING CUSTOMERS WITH

HIGH QUALITY PRODUCTS,COMPETITIVE PRICES AND EXCELLENT SERVICES

 

All rights reserved Shenyang Bona Titanium Technology Co.,Ltd. 辽icp备17016579号Powered by300.cn shenyang.300.cn

Company News
Industry News
Exhibition

Titanium Bars The Main Market

Page view
[Abstract]:
Titaniumanditsalloysduetothelargeanisotropyindexrbitislarge,TitaniumBarsandthedangeroussectionisthecircumferentialnon-strainedbiaxialtensilestressstate,thenthedangeroussectionofthecarryingcapacitythan
Titanium and its alloys due to the large anisotropy index r bit is large, Titanium Bars and the dangerous section is the circumferential non-strained biaxial tensile stress state, then the dangerous section of the carrying capacity than the r = 1 steel plate to improve a lot, limit pull The relationship between the coefficient of k and r.
 
Usually the deepening of the mild steel or aluminum plate does not need to take into account this condition, because even under the ultimate drawing coefficient of its plasticity is more than enough, Titanium Bars but titanium, especially titanium deformation capacity is limited. It can not afford to shrink from the diameter of the hair to the deformation of the diameter of the cylinder, Titanium Bars so it is often the key to determine the success or failure.
 
This is also the special place of titanium, from the listed data is easy to understand, such as TC3 titanium rod in a simple bending state of the minimum bending radius of 5.5-6 times the thickness of the sheet, if we use the usual deep drawing steel plate Filament radius of 5 times the thickness of the mold to deepen the TC3 titanium plate, it is clear that it will be broken due to bending, Titanium Bars which is a more dangerous with a tensile force, assuming that the sheet and punch four corners do not occur relative sliding , You can get the following relationship: r-mode> 2rmin + t
 
This is also caused by the properties of the titanium plate itself. Titanium Bars Titanium plate when the stability of the stability of only about half of steel or aluminum, that is easy to wrinkle, which is difficult to pass through the concave at the fillet at the corner of the vacant part, Titanium Bars coupled with the bending of titanium plate is not good, so Easy to wrinkle at the same time in the crest of the crest at the crest, that is, the so-called wrinkle. In order to avoid wrinkles, special measures are required.
 
Titanium, especially the high strength of the titanium alloy rebound than the steel plate to be several times, so sometimes the parts out of the deep, but the accuracy is too low, Titanium Bars in the drawing box shape accuracy problems become more serious.
 
Resources and very rich, due to the titanium has a series of excellent performance. Titanium industrial production came out immediately after the widespread attention. Titanium application first from the military and aviation industry began as early as 1951 the United States will use titanium on the aircraft, the former Soviet Union, the British titanium is also mainly used in the military and aviation fields. Titanium is the first for aviation, the aviation market has been the most important market for titanium, the world still accounts for 50% of the total titanium market in the 1970s, titanium excellent performance gradually in the civilian industry has been widely recognized, metallurgy, chemical , Electricity and other civilian industries on the application increased year by year, the amount of steady growth. I believe that with the new application of titanium rods and titanium alloy from time to time development and development, in short. Titanium new dosage from time to time rise, Titanium Bars the future development of new applications of titanium market prospects.
 
Resources and very rich, due to the titanium has a series of excellent performance. Titanium industrial production came out immediately after the widespread attention. Titanium application first from the military and aviation industry began as early as 1951 the United States will use titanium on the aircraft, the former Soviet Union, Titanium Bars the British titanium is also mainly used in the military and aviation fields. Titanium is the first for aviation, the aviation market has been the most important market for titanium, Titanium Bars the world still accounts for 50% of the total titanium market in the 1970s, titanium excellent performance gradually in the civilian industry has been widely recognized, metallurgy, chemical , Electricity and other civilian industries on the application increased year by year, Titanium Bars the amount of steady growth. Titanium Bars I believe that with the new application of titanium rods and titanium alloy from time to time development and development, in short. Titanium new dosage from time to time rise, the future development of new applications of titanium market prospects.